Help Me. Green, Green, Green .. ORANGE! ç_ç

I hope you can help me and I am writing on the right

My pc use Card Network + Wi-Fi Router, And possess a Network Lan, I explain my problem:

When I try to connect Nabaztag/tag
I turn on only the three green lights while the fourth (On the nose and belly) continue to flash orange.
Following the instructions, my router is set on Channel 11 while DHCP is enabled.

But I noticed one thing: if the advanced settings in Violet Piattaform insert 193.149.120.33/vl + PROXY ->NO = Three green lights. Fourth orange that flashes
r.nabaztag.com/vl + Proxy -> NO =
Two green lights. Third and Fourth that flash orange


Excuse my English very low Help Me!

Use default settings :
Advanced configuration
Authentication : OpenSystem (for a wep key) SharedKey (WPA Key)
DHCP Enabled : Yes
Local IP : 0.0.0.0
Local Mask : 255.255.255.0
Local Gateway : 0.0.0.0
DNS Server : 0.0.0.0

Proxy Server
HTTP Proxy : No
Proxy IP Address : 0.0.0.0
Proxy port : 0

General info
Violet Platform : r.nabaztag.com/vl or 193.149.120.33/vl at the end it is a "L" like Laurence

Already tried.
Continue with three green lights and a flashing orange.

Do you have a proxy? In this case your have to fill the proxy fields.

The blinking orange nose means that your rabbit can't reach the Violet servers.

I do not have any proxy. I hope ... : P that is not qualcucosa.

And what could I do?

Are you using only the wifi from the router to your computer or do you have a cable. Unplug it and retry please if you are in this case.

Do you try 11 chanel on your wifi router ?

Putting DHCP No, the nose flashes Green \ Orange> _ <


Yes, Router Wifi CHannel 11.

Yes, my computer is connected by a cable Router. I try to detach.

Use
DHCP Enabled : Yes
Local IP : 0.0.0.0
Local Mask : 255.255.255.0
Local Gateway : 0.0.0.0
DNS Server : 0.0.0.0

if you don not know how to set up your internet access your routeur will do it for you in that case.

What is your firmware? (you can see it in the rabbit set up page)

marfab a écrit:

Use
DHCP Enabled : Yes
Local IP : 0.0.0.0
Local Mask : 255.255.255.0
Local Gateway : 0.0.0.0
DNS Server : 0.0.0.0

if you don not know how to set up your internet access your routeur will do it for you in that case.

Three green lights. Sir Nose and flashing orange

Yes, Firmware 10.

Something goes wrong on Violet plateform.

What does it mean when the nose is flashing green and orange?

That means your rabbit try to reach Violet plateform

I do not know why but when I put DHCP - NO .. Blinking Green \ Orange

Do you have fixed Ip on your router? If you put your dhcp on "no" you have to give your rabbit the same ip that you gave it on your router set-up.

I set the DHCP Router for a Test, and I noticed that gives me the same results if imposed a fixed ip.

If instead of 255.255.255.0 enter 255.255.248.0 the Nose Orange flashes and Green, and it does so even if I connect to the Platform Violet by IP address

In short: Setting DHCP to NO, but without entering into any IP Rabbit me flashes Orange Verde.

If DHCP to YES .. Always orange

Speaking of the 4th Light.

Hold on 2 minutes please.

There is a thing to do if your rabbit nose is blinking orange/green.. Update the firmware. I'm going to find your the good link. But before, check if your firmware is 9 or 10 ok? You'll find if in the rabbit set-up page (maybe the second one... )

http://help.nabaztag.com/fiche.php?langue=3&fiche=45#none

My Firmware is 10.

Ok. Something is stucked in the set-up, non other way...

Can you send here somescreeshots? We need the rabbit and the router set-up page. Don't need to blur the informations, your neighbour will not come here

My Screen:











The final image shows the data in the event of a Static Ip.

Using a network FASTWEB Lan.

In addition to my real IP and DNS have not hidden else: P

There is a strange thing... If your network is not secured, your rabbit should connect to him straight. Did you tried just to light on your rabbit without pressing the button?

What's happening?

I did not understand.

Without press the button?
Could you explain better, please.

P.s. I am also using a translator: P